Bentley Continental Key Fob Troubleshooting Tips
The Bentley Continental is an incredibly impressive car to drive. Its brushed-metal accents the center stack, while gorgeous leather and wood cover its cabin. Its powerful W12 engine is capable of producing a whopping 552 break horsepower.
The Continental key fob is sealed with rubber to stop water from destroying its electronic chip. If it is submerged clean tap water or rain, it should be fine, however prolonged exposure to salt water can cause damage to the chip.
Keyless entry system
The Bentley Continental comes with a keyless entry system, which allows you to lock and unlock your car with a remote control. This is convenient and allows you to save time and effort. There are many reasons why your key fob could stop working. A few of them are the battery being dead or water damage, receiver module issues, and signal interference. In some cases the issue could be caused by a malfunction of the internal chip.
The key fob is encased by rubber to prevent water from entering the electronic chips. However, the key fob can still be soaked if exposed to soapy or salty water. This could cause damage to your chip. It is vital to clean the key fob and allow it to dry completely before returning the battery. If the key fob cannot function after drying and cleaning it's likely to be defective and needs to be replaced.
The clips made of metal on the battery of your Continental keyfob are what hold it in place and complete the circuit. If the clips are damaged or corroded they can cause contact issues. Check the battery contacts to make sure they are clean. Also, ensure that the battery is firmly installed. If you have a spare Continental key, try the key to see if it works. If the key is faulty it is possible to reprogram it using an OBDII scanner.
Battery
The key fob has an insignificant coin battery. When it is dead, the remote stops working. This is easy to diagnose and is fixable within a couple of minutes. The battery can be damaged by water, which requires replacement. The key fob may not function for a variety of reasons, including worn-out buttons, damaged contacts inside the battery, signal interference or an inactive module. It is possible to reset the system if you disconnect the 12 Volt batteries for a few seconds. This will allow the system to reset itself. Connect the positive cable first, then disconnect the negative cable.
The battery in the Bentley Continental key fob will last for up to four years based on how often you use it. The battery is fixed by steel clips. The clips should be secured, but if they are not, the remote will not work properly.
If the Continental key fob is exposed to clean tap water, it should be cleaned with a paper towel and allowed to dry before putting back the battery. If the chip is exposed to soapy or salty water, it might be fried. In these instances you'll need to purchase a new key fob.
Water damage
David doesn't think there are any major mechanical issues with this Continental with the exception of some rust on the wheel trims, and a bit of surface corrosion that has been exposed to road grit. The boot is roomy and practical with an original warning triangle strapped to the floor, and an extra wheel that can be tucked away in a space-saving fashion and a basic Bentley toolkit underneath the false floor.
The chip inside the key fob is protected by rubber seals that should keep it working even if the water is puddled. However, prolonged exposure to water can damage the chip, which is why it's recommended to remove your key fob of your pockets when you go for a swim, kayaking or rafting, canyoning or any other activity in which it might get wet.
If your key fob was submerged in water or soapy water, you can still try to save it. Make use of electronic cleaner or isopropyl ethanol to clean the chip. If your key fob still does not work after drying and cleaning it you may need to replace it. If you are looking for a Bentley Continental Key Fob, make sure it is water-resistant and factory-paired to your car.
Fault diagnosis
The Bentley Continental keyfob enables you to lock or unlock your vehicle with one click. This system is convenient and ensures security and safety while driving. There are a few things which can go wrong with your key fob. The most frequent causes are a dead battery water damage, or signal interference. There are several troubleshooting procedures you can use to diagnose the problem with a key-fob that is not working.
The battery is the first thing to check. Make sure that it is well-placed and that the retaining clips made of metal are correctly positioned. If the clips are loose, the battery may not have a good contact and won't function properly. Also, the retaining clips should be clean and free of corrosion.
A car battery that is weak is a common reason for the key fob to fail to work. bentley car keys inside your Continental must be in good condition to be able to communicate with the remote keyless entry system and the other electronic components onboard. Check your fuses and recharge the car battery when needed.
The Bentley Continental key fob sends signals to the receiver module which is located within the ignition barrel. If the signal is not received the engine will not start and the alarm will sound. If the Bentley continental key fob not working, you should consult a professional for assistance to fix the issue.